Category: DEFAULT

Oscilloscope and function generator multisim

Scale—The value of the divisions on the mimli.net get a readable display, adjust the Scale in inverse proportion to the frequency setting on the function generator or AC source—the higher the frequency, the lower (or more magnified) the time base. For example, if you want to see one cycle of a 1 kHz signal, the time base should be around 1 millisecond. Jun 05,  · How come I'm not getting a reading in any of the multimeters??? Does a function generator output an AC or DC signal? I clicked AC as its output for the oscilloscope, but these meters still don't give me a reading. Oh, and when I switch from a sine wave to a square wave, I get readings on the meters, why does this happen? Multisim and Ultiboard. I cannot figure out how to connect the Function Generator with an Oscilloscope to get Voltage and measure the frequency and duty cycle of the output voltage over the range of potentiometer resistance. I have to get this to work in multisim! I .

Oscilloscope and function generator multisim

[PUNIQGOOGLESNIPMIX-8

Watch Now Oscilloscope And Function Generator Multisim

NI Multisim: Basic operation of the two-channel oscilloscope, time: 2:10
Tags: Vijay tv lollu sabha mp4 videosLegitimus collins machete no 191, Lida rose karaoke s , Noam chomsky books pdf Jun 05,  · How come I'm not getting a reading in any of the multimeters??? Does a function generator output an AC or DC signal? I clicked AC as its output for the oscilloscope, but these meters still don't give me a reading. Oh, and when I switch from a sine wave to a square wave, I get readings on the meters, why does this happen? May 01,  · I set the function generator to output a 1 Vpeak sine wave, but when I acquire the signal with a scope, I am reading 2 Vpeak. Home Support Why Is the Function Generator Output Amplitude Doubled in NI Multisim? Why Is the Function Generator Output Amplitude Doubled in NI Multisim? Updated May 1, Reported In. meter in the lab. You will also need to use the oscilloscope, the function generator, a µF Mylar capacitor, two 10kΩ resistors, and two Ω resistors to build the actual circuits. Running Multisim: Series RC Circuit On the computer, go to START-ENGINEERING-NATIONAL INSTRUMENTS-MULTISIM. A blank schematic diagram screen will appear. Lab 2 – Function Generator and Oscilloscope 1. Objective In this lab you learn how to use the oscilloscope and function generator 2. Equipment a. Breadboard b. Wire cutters c. Wires d. Oscilloscope e. Function Generator f. 1k resistor x 2 h. Various connectors (banana plugs-to-alligator clips) for connecting breadboard to power supply and for. Multisim and Help: Multisim Help: The Function Generator is a voltage source that supplies sinusoidal, triangular or square waves. It provides a convenient and realistic way to supply stimulus signals to a circuit. The waveform can be changed and its frequency, amplitude, duty cycle and DC offset can be controlled. Multisim and Ultiboard. I cannot figure out how to connect the Function Generator with an Oscilloscope to get Voltage and measure the frequency and duty cycle of the output voltage over the range of potentiometer resistance. I have to get this to work in multisim! I . Scale—The value of the divisions on the mimli.net get a readable display, adjust the Scale in inverse proportion to the frequency setting on the function generator or AC source—the higher the frequency, the lower (or more magnified) the time base. For example, if you want to see one cycle of a 1 kHz signal, the time base should be around 1 millisecond. (1) MULTISIM DEMO INTRODUCING THE FUNCTION GENERATOR AND THE OSCILLOSCOPE. In this demo, we start to work with the function generator and oscilloscope. Both in Multisim and in the real world, function generators and especially oscilloscopes are among the most, if.

2 thoughts on “Oscilloscope and function generator multisim

Leave a Reply

Your email address will not be published. Required fields are marked *